In this section, we will try to address questions that we are asked on a weekly or monthly basis. This is not an exhaustive list and is based on current industry practices and the products that we stock in the UK. We would always advise that products and procedures are completed in accordance with manufacturer’s guidelines and that British standards are taken into account before you start your job. Hopefully you will find this informative but also appreciate that you may not have found the exact answer you were looking for. In this instance, please refer to the guides on our website or call the following numbers:
Duncan Conlan +44 7534941817 / Fraser McArthur +44 7956134481
frequently asked questions (WAKOL)
We really need to look at this in regard to the condition and the presence of Under Floor Heating (UHF).
The best advice for all calcium sulphate based floors is to remove the surface latents (according to manufacturer’s recommendations) and then take a moisture reading. Industry practice would suggest this is best done with a sealed Hygrometer over a period of at least 48 hours. In this case we would advise that British Standard (65%RH or less) be achieved before carrying on with the levelling work.
If the sub floor is free from cracks and structurally sound it can be primed with Wakol D3035 BEFORE Levelling. If there are hair -line cracks you should apply a layer of Wakol PU280 or Wakol MS330 and a subsequent layer of Wakol D3045 gritted primer before Levelling. If there are any large or wide cracks, the floor will need to be repaired before carrying on with further work. Please call us for further advice at this stage.
Once the relevant primers have been applied and had the correct time to dry, the Wakol levelling compound can be applied. We recommend Wakol Z715 for layer thicknesses up to max. 5mm. We recommend alternative Wakol Levelling compounds for thicker layers and would ask you to contact us for details.
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the age of the sub floor, the condition and the presence of Under Floor Heating (UHF).
If you have an existing sub floor in an older property, you will have to check if it has a mechanical DPC installed. You would then need to take a moisture reading. If the RH reading is above 65%. and less than 95%, then it must be treated with a moisture suppressant (DPM). We would recommend the use of Wakol MS330 or Wakol PU280 (2 coats) for this purpose. Once that layer is dry, we would then recommend the use of Wakol D3045 Gritted Primer to promote adhesion of the levelling compound. Once the primer is dry, we would recommend the use of Wakol Z715 Levelling Compound. This system is a very quick way to create your perfect sub floor and is easy to apply.
If you have a new build situation then you only need to consider if there is Underfloor Heating (UHF) or not.
If there is NO UHF and it has a mechanical DPC (New builds should have this automatically) and the base has been down for longer than 30 days then you don’t need to take a moisture reading. You can apply Wakol PU280 in 2 layers, as directed in the data sheet and carry on as detailed above. If you are unsure about anything, Take a moisture reading and follow the steps detailed previously that includes the use of Wakol MS330. If the moisture reading is in accordance with British Standards (65%RH or less) then you do not require moisture suppressant. In this instance you can apply Wakol D3035 Primer, wait for it to dry and then use the Wakol Z715 Levelling Compound to finish your sub floor preparation.
If the new build has UFH then the advice above is still correct but you must take a moisture reading first. It is possible to suppress a small amount of moisture in sand and cement sub floors with UFH but the RH reading should not exceed 85%. You can use either Wakol PU280 or Wakol MS330 for this purpose. If either Wakol primer- DPM has been used, you must apply Wakol D3045 Gritted Primer in the next layer before the Wakol Z715 Levelling Compound. If the moisture reading is in accordance with British Standards (65%RH or less) then you do not require moisture suppressant. In this instance you can apply Wakol D3035 primer, wait for it to dry and then use the Wakol Z715 Levelling Compound to finish your sub floor preparation.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the condition and potential movement
General Remarks
We understand that there are two main types of bitumen sub floors that most contractors come across and will try and deal with these below. Additionally we need to point out that bitumen can be an unstable product and any advice we offer is based on industry practices and the products that we stock in the UK.
Old bitumen adhesive residue
When old parquet floors are removed, they will often leave a layer of the residual bitumen adhesive on the surface of the sub floor below. The best industry advice is to encapsulate this with Primers and levelling compounds to create a new sub floor that is ready to receive a floor covering. At this stage, the contractor needs to make sure that any loose adhesive is subsequently removed before proceeding any further. Old bitumen can contain asbestos and so all health and safety precautions should be maintained. We would not recommend abrasion of the bitumen for this reason and care must be taken when checking its condition.
Once the condition of the bitumen residue is assessed, we would recommend the following products and processes. Firstly, apply Wakol MS330 Primer DPM in one layer. This will dry in approximately one hour depending on the undulation of the sub floor surface. Subsequently, apply Wakol D3045 Gritted Primer to promote the adhesion of the levelling compound layer. This will dry in approximately 45 minutes depending on the humidity in the atmosphere. Thereafter, apply Wakol Z715 Levelling Compound in a maximum layer of 10mm.
The products and processes above should make it easy for the user to achieve a new sub floor in a quick time frame and the adhesion of a new floor covering should be possible within 24 hours.
Cast Asphalt
Cast Asphalt has been used in the UK as a moisture suppressant layer for many years. It was common from the 50’s to the 70’s but was also used after that. Theoretically it can be encapsulated quite easily and we would recommend this rather than direct adhesion of a floor covering. Please note, old bitumen can contain asbestos and so all health and safety precautions should be maintained. We would not recommend abrasion of the bitumen for this reason and care must be taken when checking its condition.
Once the condition of asphalt is assessed, we would recommend the following products and processes. Firstly, apply Wakol D3045 Gritted Primer to promote the adhesion of the levelling compound layer. This will be dry in approximately 45 minutes depending on the humidity in the atmosphere. Thereafter, apply Wakol Z715 Levelling Compound in a maximum layer of 10mm.
The products and processes above should make it easy for the user to achieve a new sub floor in a quick time frame and the adhesion of a new floor covering should be possible within 24 hours.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the condition, potential movement and potential moisture issues.
General Remarks
We understand that there are two main types of tiled sub floors that most contractors come across and will try to deal with these below. Additionally we need to point out that the adhesion of the tiles, as well as surface contamination and potential moisture issues should be taken into account and any advice we offer is based on industry practices and the products that we stock in the UK.
Ceramic Tiles
Theoretically, it is possible to level on top of the tile surface but it is important to consider the potential issues before you start work. If your final floor covering is likely to be a wooden floor then you need to consider the tension created, the sub floor surface and the suitability of the sub floor itself. Whilst it is difficult to gauge the strength of the adhesive bond below the tile, you should look out for hollow spots as a new sub floor created with primers and levelling compound will likely tighten everything below it and could create additional problems.
If you are satisfied that the tiles are suitably strong and well bonded, you must then check for moisture issues in the Joints. Often times this is not an issue but it should be checked. Always keep in mind that the British standard is 65RH or less for all sub floor readings and we would not deviate from this
The next thing to be aware of is the likely contaminates on the surface of the tile and how best to deal with them. All tile surfaces must be cleaned with Wakol R4515 tile cleaner before any other procedures can be carried out. If this is not available, then a degreaser that contains acetone can be used as directed by the manufacturer. Tiles have to be abraded after cleaning to create a better bond. Visible scratches need to be created .We advise the use of diamond discs under a single disc machine for this process. All dust and sanding residue should be vacuumed immediately after.
If there are no moisture issues present, then Wakol D3045 Gritted Primer can be applied (after the floor has been cleaned as instructed) and left to dry. If moisture readings are above the British standard but below 95% RH, then a moisture suppressant would be advised before the use of Wakol D3045 Gritted Primer. In this case, we would recommend Wakol MS330 in one layer or Wakol PU280 in 2 layers Subsequently, Wakol Z715 Levelling Compound can be installed in a maximum layer of 10mm to create a new sub floor for the adhesion of a new floor covering. This is a quick and easy way to create the perfect sub floor that is suitable for a new installation of wood flooring the next day.
Stone and Quarry tile
This is a slightly different area to ceramics as the product has an absorbent surface. Additionally, it is possible that these types of product are in older buildings with no mechanical DPC. Just as with ceramics, it is important that the contractor assesses the situation for potential moisture issues and structural integrity before any work is carried out.
Once the contractor is satisfied, then the same processes and products can be used with one exception. As the surface is absorbent, it must be cleaned and sanded as described above and Wakol MS330 or Wakol PU280 should be applied before the Wakol D3045 Gritted Primer.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the condition and potential movement
There are many timber sub floor surfaces and it is most likely that a timber sub floor is going to move more than a solid base, even if has been adhered to a solid surface below. This could be as simple as the expansion and contraction of the timber caused by changes in temperature and humidity. It is probably best if we look at the different types of timber sub floor and provide the best advice that we can.
General Remarks
We appreciate that some timber sub floors will need levelling because of the undulation or depth variation. However, sometimes there are alternative methods that are used and we see their popularity increasing in the future. As an example, we see many contractors needing to compensate for mild surface undulation in timber sub floors and do not like to use products that add moisture to the surface build up. In this case we recommend the use of Wakol TS102 sound suppression matting. This product is a 2mm cork – polyurethane mat that comes in a 30 m roll. It is glued to the timber subfloor before the wooden floor covering is then subsequently glued to its surface.
This can be a very quick way to build up the sub floor by approximately 3mm without introducing any moisture and secures the overall specification. The additional benefit is the decibel reduction (17db) and the secure under foot feeling. The Wakol TS102 should always be glued with the same adhesive that will be used later for the final wooden floor covering. Therefore, it is important to keep that in mind before starting. As an example, if you were intending to install engineered plank with Wakol MS230, THEN THE SAME PRODUCT should be used to glue down the Wakol TS102 mat first.
Old Floor Boards (Pine on joist)
Ideally, the boards should first be replaced with more structurally sound products of the same thickness such as floor grade specification ply or chipboard. If this is not possible, then you should look at installing a floor grade product on top of the boards. This product should be screwed and glued to the boards below to make it as secure as possible. Ideally the boards below should be sanded back to remove any contaminates, vacuumed and then primed if necessary before applying the adhesive. We would recommend Wakol PU280 (1 layer) or Wakol D3055 as the primer coat. We would recommend Wakol MS260 as the adhesive to be used under the ply or chipboard.
Once you have a timber surface that is ready to receive Levelling compound we would recommend Wakol D3045 as the primer to be applied before installing Levelling compound. This will secure the adhesion of the levelling compound and make the job easier. As the base below is likely to move, you will need a fiber re-enforced levelling compound to allow for the movement. We would recommend adding Wakol AR114 fibers to Wakol Z715 Levelling Compound to result in a flexible product that is strong and will dry in the quickest possible time frame. One bag (250 g) of Wakol AR114 fibers is added to each bag (25 kg) of Wakol Z715 to achieve the correct ratio. The Levelling compound mix can be applied to the dry Wakol D3045 primer.
Always MAKE SURE that the wooden sub floor under the self-levelling compound can vent and is subject to airflow. Joisted floors usually receive air circulation underneath through air- bricks in the external walls.
Plywood
Please make sure that the ply is secure and free from contaminates before starting the process. Once this is done, we recommend the process above, starting with the Wakol D3045 Gritted Primer.
Chipboard
Some chipboards can contain adhesive inhibitors or surface contaminates. Usually a layer (I coat) of Wakol PU280 primer will seal out any issues but we cannot guarantee this and you may have to conduct your own tests to be absolutely sure. Once you are happy to proceed, we recommend the process above, starting with the Wakol D3045 Gritted Primer.
Help and advice?
This is by no means and exhaustive list of timber surfaces, but these are the most common we come across in the UK. If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usReclaimed Parquet Block
This is a question we get asked a lot and we will try to address this separately to any other question as there are many things to consider.
Some people buy reclaimed block to re-install, some people have to repair an old parquet floor or in extreme cases, entire floors will have to be removed and re-laid. As we know, the biggest issue is the bitumen, either on the back of the wooden block or on the subfloor, or both. So let us try to deal with the separate cases. We need to make sure people understand that old bitumen used to install floors many years ago should be treated with caution. It is possible that some bitumen contained asbestos and therefore careful handling is advised. We do cover this in our advice section on sub floors and insist that you call a professional body for advice if needed.
Old reclaimed block purchased to re- install in a new setting
If you have old reclaimed block and want to install them in a new setting then you first need to think about any bitumen on then the back surface. Ideally, all bitumen should be professionally removed as it is an unstable product and we cannot guarantee the adhesion etc. We know this is not always done but can only suggest that you be very careful with bitumen as it can have other issues. Then we need to think about the sub floor. It is imperative that any reclaimed material that contains bitumen residue is re-installed on a solid sub base. Whilst we do not guarantee anything with bitumen, we know that many contractors use Lecol 5500 adhesive for this purpose and it seems to work. However, if there is any movement (joisted sub floors), the bitumen residue seems to separate as the adhesive is a fixed product with very little tolerance to excessive movement.
Repairing an old parquet block floor
On occasion, contractors will have to repair (lift and re-install) a small section of a parquet floor. Often times this is a block floor that was installed with old bitumen many years ago. Many contractors will simply take out the floor from the particular area, clean it as best as they can then re-install it using Lecol 5500 adhesive. This seems to work on most occasions but we do not guarantee anything and always advise care when dealing with old bitumen.
Complete re-install of old parquet flooring with bitumen residues
Whilst this is not as common, we have seen this done in different ways. Smaller areas have been done just as the area repair mentioned above. The old parquet has been lifted, cleaned to a standard on site and then re-installed using Lecol 5500 adhesive. Additionally we have seen bigger projects where that process was not viable and we have specified a better system.
When possible, it as advisable to have the parquet professionally cleaned so it can be treated as new flooring from an adhesive perspective. Additionally, it is always better to create the best sub floor you can before starting the job.
The best industry practice (after assessing structural condition) is to encapsulate and old bitumen residue using primers and levelling compound. This way you create a good sub floor without disturbing the bitumen itself. It can be a quick process with the correct products and we would suggest the following Wakol MS330 DPM followed by Wakol D3045 Gritted Primer and then Wakol Z715 Levelling Compound.
Once the sub floor is ready and the old parquet has been professionally cleaned, you can install the floor with our products. For best results, we would suggest Wakol MS260 or Wakol PU225.
It is possible to use our other adhesives but we would ask you to contact for advice, as every job is individual.
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the age of the sub floor, the condition and the presence of Under Floor Heating (UHF). We would also need to consider the exact floor covering that will be installed and the requirements that entails.
General Remarks
With direct adhesion, it is critically important to assess the condition of the sub floor before measuring moisture or other process steps. The contractor needs to look at the structural suitability of the sub floor, the surface hardness and obvious contamination. As an example, any hollow spots would suggest a structural issue. Excessive crumbling on the surface would suggest a hardness issue. Surface staining, plaster residue or discoloration would suggest a contaminate issue. Most problems can be dealt with, but are site specific. Please call us for advice if you have questions at this stage.
If you have an existing sub floor in an older property, you will have to check if it has a mechanical DPC installed. You would then need to take a moisture reading. If the RH reading is above 75% and less than 95%, then it must be treated with a moisture suppressant (DPM). We would recommend the use of Wakol MS330 or Wakol PU280 for this purpose. If either Wakol primer- DPM has been used, you must adhere to it with the relevant Wakol adhesive within 72 hours. If this is not possible (on a very large area), only prime the area that can be adhered to in that time- frame before using the Wakol adhesive. Once that layer is dry, we would then recommend the use of the relevant Wakol adhesive for the specific wooden floor to be installed. In general terms, we would recommend Wakol MS228 or Wakol MS230 for engineered wooden floors and Wakol MS260 for solid wooden floors up to 180mm in width. However, we would ask contractors to contact us if they have any questions, as each job can be site specific.
If you have a new build situation then you only need to consider if there is Underfloor Heating (UHF) or not
If there is NO UHF and it has a mechanical DPC (New builds should have this automatically) and the base has been down for longer than 30 days then you don’t need to take a moisture reading. You can apply Wakol PU280 in 2 layers, as directed in the technical data sheet and carry on as detailed above. If you are unsure about anything, Take a moisture reading and follow the steps detailed previously. If the moisture reading is in accordance with British Standards (65%RH or less) then you do not require moisture suppressant. In this instance you can apply Wakol D3055 primer, wait for it to dry and then use the relevant Wakol adhesive to install your new wooden floor.
If the new build has UFH then the advice above is still correct, but you must take a moisture reading first. It is possible to suppress a small amount of moisture in sand and cement sub floors with UFH but the RH reading should not exceed 85% (See also the technical data sheet of the Wakol PU280 and the one of the Wakol MS330). You can use either Wakol PU280 or Wakol MS330 for this purpose. Additionally,if the moisture reading is in accordance with British Standards (65%RH or less) then you do not require moisture suppressant. In this instance you can apply Wakol D3055 primer, wait for it to dry and then use the relevant Wakol adhesive to install your wooden floor.
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the condition and the presence of Under Floor Heating (UHF).
General Remarks
With direct adhesion, it is critically important to assess the condition of the sub floor before measuring moisture or other process steps. The contractor needs to look at the structural suitability of the sub floor, the surface hardness and obvious contamination. As an example, any hollow spots would suggest a structural issue. Excessive crumbling on the surface would suggest a hardness issue. Surface staining, plaster residue or discoloration would suggest a contaminate issue. Most problems can be dealt with, but are site specific. Please call us for advice if you have questions at this stage.
The best advice for all calcium sulphate based floors is to remove the surface latents (according to manufacturer’s recommendations) and then take a moisture reading. Industry practice would suggest this is best done with a sealed Hygrometer over a period of at least 48 hours. In this case we would advise that British Standard (65%RH or less) be achieved before caring on with any work.
If there are any large or wide cracks, if the floor surface seems soft or if there are visible contaminates, please call us for further advice.
After sub floor has been assessed as free from cracks and structurally sound and not to be contaminated, it can be primed with Wakol D3055 before the new floor is installed with the relevant Wakol adhesive. If there are hair -line cracks you should apply a layer of Wakol PU280 or Wakol MS330 instead and continue with the adhesive when the primer is dry. If Wakol PU280 Wakol MS330 primer- DPM has been used, you must adhere to it with the relevant Wakol adhesive within 72 hours. If this is not possible (on a very large area), only prime the area that can be adhered to in that time- frame before using the Wakol adhesive. In general terms, we would recommend Wakol MS228 or Wakol MS230 for engineered wooden floors and Wakol MS260 for solid wooden floors up to 180mm in width. However, we would ask contractors to contact us if they have any questions, as each job can be site specific.
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the condition, potential movement, contamination, moisture and keeping in mind the final floor covering to be installed
There are many timber subfloor surfaces and it is most likely that a timber sub floor is going to move more than a solid base, even if has been adhered to a solid surface below. This could be as simple as the expansion and contraction of the timber caused by changes in temperature and humidity. It is probably best if we look at the different types of timber sub floor and provide the best advice that we can.
General Remarks
Often times, it is possible to glue directly to a timber sub floor without too much of an issue. However, sometimes you will need to overcome site specific problems such as contamination, moisture, structural stability and noise reduction. In general terms, all timber sub floors should be assessed, processed and primed as necessary before direct adhesion with the relevant Wakol adhesive. Wakol MS228 is generally recommended for engineered wooden floors and Wakol MS260 is generally recommended for solid wooden floors up to 180mm in width. Please refer to data sheets for specifics or call is with any questions at this stage.
Additionally, we see many contractors needing to compensate for mild surface undulation in timber sub floors or to reduce sound . In this case, we recommend the use of Wakol TS102 sound suppression matting. This product is a 2mm Cork foam mat that comes in a 30 m roll. It is glued to the timber subfloor before the wooden floor covering is then subsequently glued to its surface.
The main benefits are the decibel reduction (17db) and the secure under foot feeling. The TS102 should always be glued with the same adhesive that will be used later for the final wooden floor covering. Therefore, it is important to keep that in mind before starting. As an example, if you were intending to install engineered plank with Wakol MS230, THEN THE SAME PRODUCT should be used to glue down the Wakol TS102 mat first.
Old Floor Boards (Pine on joist)
Ideally, the boards should first be replaced with more structurally sound products of the same thickness such as floor grade specification ply or chipboard. If this is not possible, then you should look at installing a floor grade product on top of the boards. This product should be screwed and glued to the boards below to make it as secure as possible. Ideally the boards below should be sanded back to remove any contaminates, vacuumed and then primed if necessary before applying the adhesive. We would recommend Wakol PU280 (1 layer) or Wakol D3055 as the primer coat. We would recommend Wakol MS260 as the adhesive to be used under the ply or chipboard.
Plywood
Please make sure that the ply is dry, secure and free from contaminates before starting the process. If you suspect any contaminates, please apply Wakol PU280 in 1 layer before using the relevant Wakol adhesive.
Chipboard
Some chipboards can contain adhesive inhibitors or surface contaminates. Usually a layer (I coat) of Wakol PU280 primer will seal out any issues but we cannot guarantee this and you may have to conduct your own tests to be absolutely sure. Once you are happy to proceed, we recommend the process above.
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the condition, potential movement, contamination and keeping in mind the final floor covering to be installed. There are several types of metallic sub floor but each is usually treated the same as they have very similar characteristics.
General Remarks
In the UK we usually encounter metallic surfaces to be adhered to in one of the following scenarios. A steel or aluminum stair case, A raised access floor, or a computer floor in an I.T. Suite. Each sub floor is by its nature flexible, none absorbent and likely to have contaminates on the surface. Therefore, general rules apply to each circumstance but you can always call us for more advice.
Firstly, clean the metallic surface with a degreaser that contains acetone. This will stop the spread of any contaminates and hopefully the removal of any oily substances. The metallic surface should then be abraded with an appropriate abrasive to form a key for future bonding. If necessary, a further cleaning process can take place with the degreaser. At the very least, any sanding dust and debris should be vacuumed but additional cleaning is recommended.
Once the surface is suitably prepared, The wooden flooring can be installed with the relevant Wakol adhesive. Wakol MS228 is generally recommended for engineered wooden floors and Wakol MS260 is generally recommended for solid wooden floors up to 180mm in width. However, we would recommend Wakol PU225 2k for all solid wooden floors that are to be installed on top of a metalic surface. Please refer to data sheets for specifics or call us with any questions at this stage.
Additionally, we see many contractors needing to compensate for mild surface undulation in metallic sub floors or to reduce sound . In this case, we recommend the use of Wakol TS102 sound suppression matting. This product is a 2mm Cork foam mat that comes in a 30 m roll. It is glued to the subfloor before the wooden floor covering is then subsequently glued to its surface.
The main benefits are the decibel reduction (17db) and the secure under foot feeling. The TS102 should always be glued with the same adhesive that will be used later for the final wooden floor covering. Therefore, it is important to keep that in mind before starting. As an example, if you were intending to install engineered plank with Wakol MS230, THEN THE SAME PRODUCT should be used to glue down the Wakol TS102 mat first.
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usWe really need to look at this in regard to the condition, potential movement and potential moisture issues.
General Remarks
We understand that there are two main types of tiled sub floors that most contractors come across and will try to deal with these below. Additionally we need to point out that the adhesion of the tiles, as well as surface contamination and potential moisture issues should be taken into account and any advice we offer is based on industry practices and the products that we stock in the UK.
Ceramic Tiles
Theoretically, it is possible to adhere to the top of the tile surface but it is important to consider the potential issues before you start work. If your final floor covering is likely to be a wooden floor then you need to consider the tension created, the sub floor surface and the suitability of the sub floor itself. Whilst it is difficult to gauge the strength of the adhesive bond below the tile, you should look out for hollow spots as a new floor created with primers, adhesives and wooden flooring will likely tighten everything below it and could create additional problems.
If you are satisfied that the tiles are suitably strong and well bonded, you must then check for moisture in the Joints. Often times this is not an issue but it should be checked. Always keep in mind that the British standard is 65RH or less for all sub floor readings and we would not deviate from this
The next thing to be aware of is the likely contaminates on the surface of the tile and how best to deal with them. All tile surfaces must be cleaned with Wakol R4515 tile cleaner before any other procedures can be carried out. If this is not available, then a degreaser that contains acetone can be used as directed by the manufacturer Duncan: we cannot guarantee this. Tiles need to be abraded after cleaning to create a better bond. A diamond abrasive on a single disc machine or similar can achieve this. Scratches created should be visible after the process. Once complete, the floor will need to be thoroughly vacuumed before applying the Wakol PU280 or Wakol MS330 primer.
Once the primer is dry, the relevant Wakol adhesive can be used to install the new wooden floor. In general terms Wakol MS228 or Wakol MS230 is recommended for engineered floors and Wakol MS260 is recommended for solid wooden floors up to 180 mm in width.
Stone and Quarry tile
This is a slightly different area to ceramics as the product has an absorbent surface. Additionally, it is possible that these types of product are in older buildings with no mechanical DPC. Just as with ceramics, it is important that the contractor assesses the situation for potential moisture issues and structural integrity before any work is carried out.
Once the contractor is satisfied, then the same processes and products can be used with one exception. As the surface is absorbent, it must be cleaned as described above and Wakol MS330 or Wakol PU280 should be applied before the relevant Wakol adhesive.
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usfrequently asked questions (LOBA)
Loba was founded in 1922. We are looking forward to celebrating the centenary year in 2022. This is nearly 100 years of expertise in the field of finishing and maintaining wooden and parquet floors.
Loba headquarters and manufacturing is based in Ditzingen, near Stuttgart, Germany. Today, you will find the Loba brand excelling in its field, in almost every country in the World. Loba believes in the highest quality of standards, which is key to the continued success, development and progress of this Global brand.
In 2018 Loba was purchased by Wakol, a leading German supplier of under floor accessories, such as primers, levelling compounds and adhesives for floor installation. Together they offer connected systems. Adhesives, lacquers and oils manufactured by either company are compatible with each other and work to produce a synergic result. This is unique in the flooring industry and contractors can now be sure that adverse reactions can be avoided by using the Wakol and Loba product range. A completely coordinated system can be specified and applied, from the subfloor creation to the maintenance of the floor surface and everything in between.
Loba products
Loba products bring out the very best in every floor. Both in terms of quality and aesthetic. In the UK, we specialise in the Loba products specific to wooden floors and can offer products in the following areas of finishing:
- Primers
- Lacquers
- Impregnation oils
- Hardwax oils
- Maintenance products
- Cleaning agents
Loba products have been developed with a lot of attention, including (but not restricted to) the following areas:
- Durability, for longevity and peace of mind
- Resistance to external influences such as chemicals, pollution, scratches and day to day wear and tear
- Fast drying
- Hassle-free and easy to apply
- Many design options, colours and sheen levels
- Complying with the strictest requirements with regard to the environment and personal safety
Help and advice?
If you need help and advice on something of this topic that is not covered, please contact us and we will try our best to answer your questions.
Contact usPlease follow this link for our latest brochure:
Download brochurePlease follow this link for a list of our Loba distributors:
Loba distributorsOur distributors all hold stock of our sample boxes for ProColor (solvent based stain for a lacquered finish), ImpactOil (Impregnating oil) and Markant (Hardwax oil). Links to these can be found here:
ProColor 100ml sample box: https://lecoluk.com/product/sample-box-loba-procolor/
ProColor sample box folder: https://lecoluk.com/product/sample-box-loba-procolor/
ImpactOil 100ml sample box: https://lecoluk.com/product/sample-box-lobasol-hs-2k-impactoil/
ImpactOil sample box folder: https://lecoluk.com/product/sample-box-loba-oils-and-colours/
Markant 100ml sample box: https://lecoluk.com/product/sample-box-lobasol-markant/
Markant sample box folder: https://lecoluk.com/product/sample-box-loba-oils-and-colours/
Please follow this link to book your appointment
Book demoAll information on all the Loba finishes stocked in the UK can be found at this link:
Loba finishesPlease check the SUITABILITY LIST for all common and exotic wood species with our Loba sealer, found on the matrix on this link:
Suitability listYes, for Loba, please contact Fraser McArthur. In Fraser’s absence, please contact Duncan Conlan
Contact usFull product information can be found here, but for your convenience, please be advised as follows:
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Universal 100 / 100 – 120 ml/m2 (8-10 m2/l).
- LOBATOOL® roller Microfaser 100-120 / 80-100 ml/m² (10-12 m²/l).
- Due to the reduced volume of application, the use of the roller Microfaser leads to less wood swelling.
- LOBATOOL® trowel / 1st application approx. 40 ml/m² (25m²/l), 2nd application approx. 20 ml/m² (50m²/l)
- Do not intermediate-sand the primer. If an adequate layer thickness is achieved (roller application, poorly absorbent substrate), the surface can be worked over with a single-disc machine and LOBATOOL® maroon pad underneath. Carefully remove dust before overcoating.
Drying time LOBADUR® WS EasyPrime
- The earliest the floor can be varnished over in the case of roller applications is approx. 60 minutes and 30 minutes for trowel applications, but within 24 hours.
- If there are drying delays, wait until completely dry.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® WS Life is a waterborne 1-Component finish for wooden floors. Full product information can be found here, but for your convenience, please be advised as follows:
- We recommend firstly applying a prime coat – EasyPrime or PrimaSeal Plus
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Deluxe 120 / 100-120 ml(g)/m² = 8-10m²/l(kg)
- LOBATOOL® roller Microfaser 100-120 / 80-100 ml(g)/m² = 10-12m²/l(kg)
Intermediate sanding
- Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will achieve an even finish. Use LOBATOOL® perforated pad P120 or finer, alternatively Sanding Net P120 or finer. Carefully remove dust before overcoating.
Drying time LOBADUR® WS Life
- Earliest possible recoating after 4-6 hours.
- Careful use possible after 4-6 hours.
- Earliest possible intermediate sanding after 8-10 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® WS Viva is a waterborne 1-Component finish for wooden floors. Full product information can be found here, but for your convenience, please be advised as follows:
- We recommend firstly applying a prime coat – EasyPrime or PrimaSeal Plus
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Deluxe 120 / 100-120 ml(g)/m² = 8-10m²/l(kg)
- LOBATOOL® roller Microfaser 100-120 / 80-100 ml(g)/m² = 10-12m²/l(kg)
Intermediate Sanding
- Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will achieve an even finish. Use LOBATOOL® perforated pad P120 or finer, alternatively Sanding Net P120 or finer. Carefully remove dust before overcoating.
Drying time LOBADUR® WS VIVA
- Earliest possible recoating after 4-6 hours.
- Careful use possible after 4-6 hours.
- Earliest possible intermediate sanding after 8-10 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® 2K Invisible Protect AT is a waterborne surface protection for parquet and hardwood floors. For extremely heavy wear. The natural look and feel of the untreated wood is maintained. The virtually invisible layer is also extremely scratch-resistant thanks to the use of the highest-quality raw materials. Elastic, excellent chemical and abrasion resistance. Full product information can be found here, but for your convenience, please be advised as follows:
- No Prime coat required
- Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBATOOL® Mixing Container or a scale to weigh out the components.
- Usable up to 2 hours after mixing.
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Deluxe 120 / 110-130 ml(g)/m2 = 8-9 m2/l (kg)
- Using smaller pile rollers will require a third coat of varnish applied
Intermediate sanding
- Able to recoat without intermediate sanding within the first 24 hours.
- After this time, an intermediate sanding is necessary.
- An intermediate sanding before the last application will achieve an even finish.
- Use LOBATOOL® perforated pad P120 or finer, alternatively Sanding Net P120 or finer.
- Carefully remove dust before overcoating.
Drying time
- Earliest possible recoating after 4-6 hours.
- Careful use possible after 4-6 hours.
- Earliest possible intermediate sanding after 8-10 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® WS 2K Supra AT is the hardest waterborne finish on the market Ceramic-reinforced waterborne 2-Component polyurethane finish. For extremely heavy wear. The exceptionally high resistance to scratching and durability of the finish gives wooden flooring long-lasting protection. It can also be used fully after a curing time of just 24 hours. Elastic, excellent chemical and abrasion resistance. Full product information can be found here, but for your convenience, please be advised as follows:
- We recommend firstly applying a prime coat – EasyPrime or PrimaSeal Plus
- Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBATOOL Mixing Container or a scale to weigh out the components.
- Usable up to 2 hours after mixing.
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Deluxe 120 / 100-120 ml(g)/m² = 8-10m²/l(kg)
- LOBATOOL® roller Microfaser 100-120 / 80-100 ml(g)/m² = 10-12m²/l(kg)
Intermediate sanding
- Able to recoat without intermediate sanding within the first 24 hours.
- After this time, an intermediate sanding is necessary.
- An intermediate sanding before the last application will achieve an even finish.
- Use LOBATOOL® perforated pad P120 or finer, alternatively Sanding Net P120 or finer.
- Carefully remove dust before overcoating.
Drying time
- Earliest possible recoating after 4-6 hours.
- Careful use possible after 4-6 hours.
- Earliest possible intermediate sanding after 8-10 hours.
- Full traffic capability and coverage after 24 hours.
- First care after 3 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBASOL® Markant Color is a colored natural hardwax oil. High-quality, layer-building oils accentuate the natural look of the wood and at the same time achieve excellent resistance to dirt and water. Full product information can be found here, but for your convenience, please be advised as follows:
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants. Room temperature +15°C to +25°C, relative humidity 40% to 65%, material temperature +18°C to +25°C. Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- The innate color of the wood used, its structure and its pore properties, as well as the fineness of the sanding pattern, also have a major impact on the color that can be achieved. We strongly recommend to produce a color sample on the original wood using site-appropriate sanding techniques to check the result by yourself and if necessary for approval by the project client.
- Note the LOBA “Sanding instructions for coloring parquet flooring”.
- Before using the color variants, we recommend carrying out a test application to assess the color tone that can be achieved and the overall visual effect. The colors can be mixed with each other. For lightening, or to reduce the coverage, the transparent variant can be added in. For an even color coverage, pigment saturation is required; dilution should therefore be carried out at most with three parts of transparent and one part color variant.
- If more than one container is being used for large areas, the total quantity must be mixed before work commences in a large container.
- On flooded surfaces, the deep penetration of the pigments into the wood means that it is not possible to restore the surface to its original condition.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the “Connected Systems” Matrix: loba.de/connected-systems
- Thinner To lighten the shade or to reduce the coverage, mix with Markant semigloss. Max. 3 parts transparent to one part color.
Application tool/application rate
- Trowel application: LOBATOOL® trowel / approx. 20 ml/m² (50m²/l)
- Roller and brush application: LOBATOOL® oil roller Microfaser 60-80 or LOBATOOL®
- Oilbrush / approx. 60-100ml/m² (12m²/l)
Drying time
- Earliest possible overcoating after 12 hours, however within 24 hours.
- Can be walked on after 12 hours.
- Usable after 24 hours.
- Coverage after 10 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBASOL® Markant is a natural hardwax oil. High-quality, layer-building oils accentuate the natural look of the wood and at the same time achieve excellent resistance to dirt and water. Full product information can be found here, but for your convenience, please be advised as follows:
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants. Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C. Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® Bucket before applying.
- Shake the contents well
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- Trowel application: LOBATOOL® trowel / approx. 20 ml/m² (50m²/l)
- Roller and brush application: LOBATOOL® oil roller Microfaser 60-80 or
- LOBATOOL® oilbrush / approx. 80ml/m² (12m²/l)
Drying time
- Earliest possible overcoating after 12 hours, however within 24 hours.
- Can be walked on after 12 hours.
- Usable after 24 hours.
- Coverage after 10 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® WS Life is a Waterborne 1-Component finish for wooden floors. Full product information can be found here, but for your convenience, please be advised as follows:
- We recommend firstly applying a prime coat – EasyPrime or PrimaSeal Plus
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Deluxe 120 / 100-120 ml(g)/m² = 8-10m²/l(kg)
- LOBATOOL® roller Microfaser 100-120 / 80-100 ml(g)/m² = 10-12m²/l(kg)
Intermediate sanding
- Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will achieve an even finish. Use LOBATOOL® perforated pad P120 or finer, alternatively Sanding Net P120 or finer. Carefully remove dust before overcoating.
Drying time
- Earliest possible recoating after 4-6 hours.
- Careful use possible after 4-6 hours.
- Earliest possible intermediate sanding after 8-10 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® WS Viva is a waterborne 1-Component finish for wooden floors. Full product information can be found here, but for your convenience, please be advised as follows:
- We recommend firstly applying a prime coat – EasyPrime or PrimaSeal Plus
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Deluxe 120 / 100-120 ml(g)/m² = 8-10m²/l(kg)
- LOBATOOL® roller Microfaser 100-120 / 80-100 ml(g)/m² = 10-12m²/l(kg)
Intermediate Sanding
- Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will achieve an even finish. Use LOBATOOL® perforated pad P120 or finer, alternatively Sanding Net P120 or finer. Carefully remove dust before overcoating.
Drying time LOBADUR® WS VIVA
- Earliest possible recoating after 4-6 hours.
- Careful use possible after 4-6 hours.
- Earliest possible intermediate sanding after 8-10 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® WS 2K Fusion is a waterborne 2-Component polyurethane finish for wooden floors. For extremely heavy wear. Elastic, excellent chemical and abrasion resistance. Full product information can be found here, but for your convenience, please be advised as follows:
- We recommend firstly applying a prime coat – EasyPrime or PrimaSeal Plus
- Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBATOOL Mixing Container or a scale to weigh out the components.
- Usable up to 2 hours after mixing.
- The surface must be sanded properly, wood moisture content max. 12%
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® roller Deluxe 120 / 100-120 ml(g)/m² = 8-10m²/l(kg)
- LOBATOOL® roller Microfaser 100-120 / 80-100 ml(g)/m² = 10-12m²/l(kg)
Intermediate sanding
- Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary.
- An intermediate sanding before the last application will achieve a more even finish.
- Use LOBATOOL® perforated pad P120 or finer, alternatively Sanding Net P120 or finer.
- Carefully remove dust before overcoating. Drying time
- Earliest possible recoating after 4-6 hours.
- Careful use possible after 4-6 hours.
- Earliest possible intermediate sanding after 8-10 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® Whitener is an additive that is added to water-based LOBADUR® primers and finishes for a smooth brightening of wood floors. The intensity of the whitening may be individually controlled by variable application in one or more layers. Full product information can be found here, but for your convenience, please be advised as follows:
- Avoid lapmarks: The darker the substrate, the higher the risk of lapmarks. Material must not be poured on the floor. Use LOBATOOL® finish bucket and apply directly with a recommended applicator.
- The use in matt finishes reduces the risk of lapmarks.
- Preferably use in at least two layers.
- Apply LOBADUR® WS products with Whitener as evenly as possible, avoiding puddles and overlaps. Ensure an even application rate. Apply edge areas with the LOBATOOL edge roller.
- The colour effect of LOBADUR® Whitener depends on the type of wood. In order to assess the achievable color shade and the overall optical effect, we recommend to prepare a color sample on the original wood for your own examination and, if necessary, for approval by the building owner.
- Wood species with water-soluble wood components (e.g. tannic acid) whose intensity can vary within a surface can influence the effect of LOBADUR® Whitener.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions.
Mixing
- Shake LOBADUR® Whitener and finish well.
- Add just before application.
- Add a maximum of one container of 1x80ml to 5L/kg of finish.
- Shake or stir in thoroughly (also possible mechanically with a LOBATOOL® paint mixer).
- In the case of two-component systems, LOBADUR® Whitener is added after the hardener is worked into the mass!
- 1K finish mixed with LOBADUR® Whitener must be applied within 24 hours,
- 2K finishes within the indicated application time. Longer stability is not guaranteed.
Suitability
- Can be combined with all LOBADUR® WS finishes and primers. The processing properties of the finish, its product combinability and the drying time remain unchanged. Please note the TI of the corresponding finish.
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBASOL® HS 2K Impact Oil, HighSolid oil based on natural ingredients. Accentuates the natural character of the wood and achieves excellent properties. As a result, suitable for public and private areas with high quality demands, and can even be used in wet areas. Due to its good penetration properties the wood will be preserved, but remains porous and breathable. Compared to regular 1C oils the 2C technology achieves a quicker curing, a lower susceptibility to dirt and a better water and chemical resistance. Full product information can be found here, but for your convenience, please be advised as follows:
- Stir the mixture, add the hardener in a ratio of 10:1 and stir in well (also possible by machine with LOBATOOL® Paint mixer).
- If partial quantities are to be mixed, these must be weighed out.
- After mixing, transparent oil can be used for 2 hours while colour oil can be used for 1 hour.
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants. Room temperature +15°C to +25°C, relative humidity 40% to 65%, material temperature +18°C to +25°C. Ensure working areas are adequately ventilated.
- Shake the contents well.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at wingis-online.de.
- The product is supplied ready for use and must not be diluted!
Application tool/application rate
- LOBATOOL® oil roller Microfaser 60-80 or LOBATOOL® trowel / 30-60 ml (g)/m2, depending on the absorbency of the substrate.
- Equalise with LOBATOOL® special pad beige.
Drying time
- Can be walked on after 12 hours.
- Usable after 24 hours.
- Coverage after 5 days
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact usLOBADUR® ProColor is a stain for wooden floor based on solvents. For the professional staining of parquet and hardwood floors. Dries reliably and lap-free regardless of climatic conditions and can be easily varnished over with LOBADUR® waterborne finishes. Full product information can be found here, but for your convenience, please be advised as follows:
- The surface must be sanded properly, wood moisture content max. 12%.
- The floor must be dry and free from any old coatings, oil, grease, wax, silicone, sanding dust and other contaminants.
- Room temperature +15°C to +25°C, relative humidity 40% to 75%, material temperature +18°C to +25°C.
- Ensure working areas are adequately ventilated.
- Transfer material to a LOBATOOL® varnish bucket before applying.
- Shake the contents well.
- The innate colour of the wood used, its structure and its pore properties, as well as the fineness of the sanding pattern, also have a major impact on the colour that can be achieved. We strongly recommend to produce a colour sample on the original wood using site-appropriate sanding techniques to check the result by yourself and if necessary for approval by the project client.
- Note the LOBA “Sanding instructions for colouring parquet flooring”.
- Before using the colour variants, we recommend carrying out a test application to assess the colour tone that can be achieved and the overall visual effect. The colours can be mixed with each other. For lightening, or to reduce the coverage, the transparent variant can be added in. For an even colour coverage, pigment saturation is required; dilution should therefore be carried out at most with three parts of transparent and one part colour variant.
- If more than one container is being used for large areas, the total quantity must be mixed before work commences in a large container.
- On flooded surfaces, the deep penetration of the pigments into the wood means that it is not possible to restore the surface to its original condition.
- Observe the general and, if available, the product-specific health and safety instructions. More specific information relating to GISCODE can be found in the usage instructions, which are available at www.wingis-online.de.
- To lighten the shade or to reduce the coverage, mix with the transparent variant. Max. 3 parts transparent to one part colour.
Application tool/application rate
- LOBATOOL® trowel / approx. 30-50ml/m² (20-33m²/l or 15-20m²/container) or
- LOBATOOL® oil roller Microfaser 60-80 as a wiper (do not roller) / approx. 30-50ml/m² (20-33m²/l or 15-20m²/container) depending on the absorbency of the substrate.
- Water-popping prior to the application, increases the total material consumption up to double the quantity.
- Equalise with LOBATOOL® normal pad beige.
- To intensify the colour, water-popping in advance is possible. Regard our technical tips when doing so: see “Water-popping of wooden floors and colouring with ProColor”.
Drying time
- Earliest possible overcoating after 12 hours.
- Apply any of Loba’s waterborne varnishes to finish
Help and advice?
If you need help and advice on something that is not covered, please contact us and we will try our best to answer your questions.
Contact us.